> ## Documentation Index
> Fetch the complete documentation index at: https://docs.cloneable.ai/llms.txt
> Use this file to discover all available pages before exploring further.

# Cable Tracing troubleshooting

> Find the cause and fix for problems with opening Cable Tracing, clicking parts, cards, heights, saving your trace, and DDS and SPIDAcalc exports.

Look here when something in Cable Tracing doesn't work the way you expect. For problems listed in the Issues panel, see [Find and fix issues](https://docs.cloneable.ai/guides/tracing/issues-and-fixes.md).

## Starting Cable Tracing

> [accordion] The Cable Tracing button is missing
>
> **Cause:** Cable Tracing is turned on separately for each organization, and it isn't on for yours.
>
> **Fix:**
>
> 1. Ask Cloneable support to turn it on.
> 2. When it's on, open **Utility Map**, choose one job and click **Cable Tracing**.
>
> For the full checklist, see [Prepare a job for Cable Tracing](https://docs.cloneable.ai/guides/tracing/before-you-start.md).

> [accordion] The What is here? list has no framings or parts
>
> **Cause:** this job's configuration has no pick list.
>
> **Fix:** ask an admin to add one under **Settings → Configurations → Pick list**, using your DDS standards or your SPIDAcalc client file.

> [accordion] A pole card has no photo
>
> **Cause:** the pole has no measurement photo, or the phone that captured it hasn't finished syncing.
>
> **Fix:** ask the crew to open the Cloneable app and let it sync.

## Clicking and cards

> [accordion] A click landed on the wrong part
>
> **Fix:**
>
> 1. In the bar at the bottom of the map, click **Undo**.
> 2. Scroll on the photo to zoom in, and click the part again.
> 3. To zoom back out, click **Fit photo**.

> [accordion] The card asks you to click the crossarm again
>
> **Cause:** Cloneable needs the spot where the arm mounts on the pole. This applies to a double crossarm and to a crossarm on the side of the pole facing the camera.
>
> **Fix:** click the pole at the height of the bolt that holds the arm.

> [accordion] The card shows Which wire is this?
>
> **Cause:** Cloneable can't tell which wire from the previous pole is on this part.
>
> **Fix:** choose the wire from the list. To change it later, click **Another wire…** on the card.

> [accordion] The wires on the photo run left to right in the opposite order
>
> **Cause:** the photo was taken from the other side of the line.
>
> **Fix:** in the bar, click **Flip**. The map turns so the cards match the photos, and the photo itself is never mirrored. If two wires show as crossed, compare both poles with their photos before you click **Swap them**.

> [accordion] The next pole offers the wrong framing
>
> **Fix:** click **Not here**, click the photo, and choose the framing that's on the pole.

> [accordion] A wire doesn't go to this pole
>
> **Fix:** in the wire list, choose the option that matches the wire:
>
> | If the wire | Choose |
> | - | - |
> | Runs past this pole | **Passes this pole** |
> | Isn't on this pole, and you want to place it later | **Not here** |
> | Ends on the previous pole | **Ends at** and that pole's name, on the card |

## Heights

> [accordion] A part has no height
>
> **Cause:** the photo isn't calibrated, or heights are turned off for the configuration.
>
> **Fix:** calibrate the photo, or type the height on the part's card. To turn heights on, an admin can turn on **Annotator heights** in the configuration's **Project setup**.

> [accordion] A midspan height looks wrong
>
> **Fix:**
>
> 1. Check the wire's heights at both poles.
> 2. Check which wire you clicked on the midspan photo.
> 3. Look for **Swapped?** tags. See [Common issues](https://docs.cloneable.ai/guides/tracing/issues-and-fixes.md#common-issues).

> [accordion] A wire on a post or bracket shows a different height than your click
>
> A wire on a post or bracket shows and exports at the height of the post's bolt, because that's where the part mounts.

## Saving

> [accordion] The bar shows Unsaved changes
>
> **Cause:** Cloneable saves when you stop making changes and when you leave Cable Tracing.
>
> **Fix:** wait a few seconds.

> [accordion] Not saved, retrying
>
> **Cause:** a save didn't go through, so Cloneable is trying again.
>
> **Fix:** keep the tab open. If a **Not saved** row appears in the Issues panel, Cloneable couldn't save that change. Click the row to save again.

> [accordion] Saved cable tracing didn't load
>
> **Fix:** in the bar, click **Try again** before you change anything. Changes you make before the trace loads aren't saved.

## Exports

> [accordion] The DDS file is missing a wire
>
> **Cause:** the wire has no conductor from your standards, or it's on only one pole.
>
> **Fix:** open the export dialog and read the warning, which names the pole. See [Common DDS warnings](https://docs.cloneable.ai/guides/integrations/dds/export.md#common-dds-warnings).

> [accordion] The DDS file is missing a crossarm
>
> **Cause:** the arm isn't in a framing.
>
> **Fix:** click the **Not in a framing** tag on the arm and choose a framing.

> [accordion] A guy wire is missing from an export
>
> **Cause:** the guy wire isn't tied to an anchor, or the pole has no anchor on the map.
>
> **Fix:** if the anchor is missing, add it on the map. Then tie the guy wire to it on the guy wire's card.

> [accordion] The SPIDAcalc export shows Check again
>
> **Cause:** an edit is still saving, or an edit didn't save.
>
> **Fix:** wait a moment, and then click **Check again**. If an edit didn't save, make the edit again, or reload the map to discard it.

> [accordion] Problems after opening the file in SPIDAcalc
>
> See [SPIDAcalc troubleshooting](https://docs.cloneable.ai/guides/integrations/spidacalc/troubleshooting.md).

## Contact support

If the problem continues, send us a message from the chat in Cloneable. Include the job's name and the exact wording you see on screen.


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.